Instructions for Etisalat D-Link Mobile Router (DWM-157) installation in Windows 10.

The adapter and the service where provided with no instructions, so I had to google a bit. Maybe it works “automatically” for you. Otherwise, try these steps to get the Etisalat mobile service working. The list below looks quite long, but don’t despair, its not that complicated. I just like using lots of numbers for steps.

etisalat dlink mobile
  1. Insert SIM card. Snap out the big section and leave the smaller SIM card attached to this bigger adapter section.
  2. Insert device in USB port
  3. Installation doesn’t start automatically? good, it shouldn’t (better security). Now go look for the installer. The device should show up as a USB drive, so look in “This PC”
  4. Start and follow the installer directions, nothing to it. Done, close.
  5. Click on the D-Link Connection Manager on your desktop (Or Programs)
  6. It took one day for Etisalat to make the service available for me. Before I got service, this is what my panel looked like:
etisalat dlink connection manager

After the service was activated, looking better:

etisalat dlink connection manager
  1. But no pages were loading. So there is this APN thing.
  2. On the D-Link manager, click the gears icon (Options)
  3. Go to Profile Management
  4. New
  5. Profile name: Internet
  6. APN:
  7. Access Number: *99#
  8. User name and Password – leave blank
  9. Authentication: PAP
  10. Save
  11. Make it Default. You may try the Connect button and see if it works. Once connected, your panel will look like this:
etisalat dlink connection manager

Windows XP has a built in security center that monitors the activities or existence of Automatic Updates, Windows Firewall and virus protection provided by third party anti virus software.

When one or more security component do not been installed, or been disabled or turned off, or not working, Windows Security Center will highlight the section in yellow or red for warning and critical attention. Security Center service will also pop up a warning message with red or yellow icon that your computer might be at risk at notification area (system tray).

Security Center in Windows XP can be disabled or turned off so that the system will not monitor or check whether or not the antivirus software existed, properly installed and running, or whether the firewall and Automatic Updates been disabled or bypassed.

  1. Click on Start button, then select Control Panel.
  2. Select “Administrator Tools” (if you don’t see it, double click on “Performance and Maintenance” first).
  3. Double click “Services”.
  4. Find and double click on the service named “Security Center”. Alternatively right click on “Security Center”, and select “Properties” on right click menu.
  5. In the “General” tab, beside the “Startup type:”, change the setting from Automatic to “Disabled”. This will permanently disable Security Center forever, even after you reboot and restart the computer system.
  6. The click on “Stop” button at the bottom of the dialog window to stop Security Center immediately during current log on session.

After disable the Security Center, you won’t be any security warning (Your computer might be at risk, and etc) nag again. By turning it off, your system may be expose to virus, malware and spyware threat too if your anti virus program is not functioning unknowingly or accidentally.

To enable or turn Security Center back on, simply select “Automatic” at step 5 above. If you want to run Security Center for a while or immediately after set to “Automatic” as Startup type, click on “Start” button.

Google will have a bazillion different listing s for this, all complicated processes. Myabe i just got lucky with this one, but try it first!

My problem was an install from windows update the often gets corrupted, xml4. Whenever I shut down my computer, Windows said it is installingupdate 1 of 1. It toggled between the message of “Installingupdate 1 of 1” and a don’t turn off the computer, it would shut down by itself. But it will stay on that until I force shut down, and still be there whenever I want to restart or shutdown. If this is you:

  1. Disable automatic updates > more on that
  2. Download “msxml4-KB936181-enu.exe” from the Microsoft site, not Windows Update.
  3. Run the program > Remove
  4. Reboot
  5. Run the program again > Install
  6. Turn on Automatic Updates. I left automatic updates OFF, but the problem should be fixed so you shouldn’t have to.